Wheel Repair Technicians Jerome ID

There are many tips to sprucing up your car’s paint or preventing the interior from looking worn in the first place, but the wheels need attention too. If your painted metal is looking the worse for wear, here’s how to repair it yourself without spending a fortune.

Idaho Electric Motor Service
(208) 736-8383
1196 Addison Avenue West
Twin Falls, ID
Services
Auto Service & Repair, Water Well Drilling & Service, Electric Motor Parts & Repair, Armature Sales & Service
Products
Bearings, Electric Motors, Rebuilt, Pump Motors, New Rebuilt Used

Bart''s Signs Plus
(208) 324-5936
347 N 400 E
Jerome, ID
Services
Auto Body

Walmart Tire & Lube Express
(208) 324-4333
2680 S Lincoln Ave
Jerome, ID
Specialty
Lubrication Service
Hours
Mon:8:00 am-7:00 pm
Tue:8:00 am-7:00 pm
Wed:8:00 am-7:00 pm
Thu:8:00 am-7:00 pm
Fri:8:00 am-7:00 pm
Sat:8:00 am-7:00 pm
Sun:8:00 am-6:00 pm
Payment
Cash, Check, Credit Card

Crumrine Automotive Restoration Sevice
(208) 644-6471
18 Butte Dr
Jerome, ID
 
Ave Automotive Repair NAPA Auto
(208) 324-3127
47a E 100 S
Jerome, ID
 
The Automotive Clinic, Inc.
(208) 734-1333, 001-2004
577 Blue Lakes Boulevard North
Twin Falls, ID
Certifications
Blue Seal Certified
Membership Organizations
National Institute for Automotive Service Excellence (ASE)

Data Provided by:
A Sign by Sally
(208) 324-2914
1604 N Elm Street
Jerome, ID
Services
Truck Lettering

Con Paulos Chevrolet-Pontiac-Gmc
(208) 644-2160
251 Golf Course Rd
Jerome, ID
 
Jerome Auto Body
(208) 324-7488
361 Golf Course Road
Jerome, ID
Services
Alignment Repair

Riverside Boot and Saddle
(208) 324-0400
322 W Yakima
Jerome, ID
Services
Trailer Repair

Data Provided by:

DIY Wheel Repair

Do-It-Yourself Wheel Repair By Alison Lakin, Associate Editor

Scratched your wheels? We know exactly how annoying that can be. There are many tips to sprucing up your car’s paint or preventing the interior from looking worn in the first place, but the wheels need attention too – especially since they usually take the brunt of urban driving; parallel parking and curbside drop-offs are a rim’s worst nightmare. If your painted metal is looking the worse for wear, here’s how to repair it yourself without spending a fortune.

First, you’ll need the following materials:
Scratch filling primer
Wheel paint (to match your specific wheel color)
Clear lacquer
Paint thinner
Bondo spot putty
Sand paper 240 and 400 grit
Masking tape

Step 1: Remove the wheel from the car. If you choose to keep it on, make sure to fully cover the car with a cloth or paper so as to seal it from the spray of the paint.
 
Step 2: Clean the wheel. Soap-up, scrub and shine that puppy. Then use paint thinner to specifically clean the damaged area, nothing more. You want to remove all polishes and waxes from the surface in order to properly repair it, which means you’ll need to really rub the area, wipe it down and repeat.

Step 3: Once the damaged area is completely clean, you’ll need to prepare the wheel for sanding. If the tire is still on, use the masking tape to cover the area underneath where the wheel meets the tire. You can use this time to completely cover the tire to protect it from paint as well. It may be a pain, but scraping paint spray off the rubber is much worse.

Step 4: Gently sand the damaged area using 240-grit sandpaper. Once you’ve sanded it down a bit, wipe the area clean and apply the putty to the scrape. Just cover the specific area and don’t worry about getting it flat and smooth because you’ll be sanding it down. Let the putty completely dry before attempting to sand it smooth using the 400-grit sandpaper. You want to make sure it feels flush to the original wheel surface – a flat block will help to create the desired effect.

Step 5: Once again, if the wheel has not been removed from the car and tire you’ll need to fully protect any exposed areas you don’t want flakes of paint to stick to. It’ll happen, trust us.

This is where the scratch filling primer comes in. Spray it on the repair area, let dry and then sand it down with 400-grit or finer sandpaper. Add more putty if there are any uneven areas and repeat. It’s very important to clean off the overspray with a rag immediately after spraying the primer and paint. There’s no reason to get paint anywhere but the area on which you’re working.

Step 6: Now comes the painting. You’ll want to read the instructions on the spray can for the most correct application techniques. We’d recommend testing the spray paint out on some scrap metal before applyi...

Click here to read the rest of the article from DriverSide