Wheel Repair Technicians Mandan ND

There are many tips to sprucing up your car’s paint or preventing the interior from looking worn in the first place, but the wheels need attention too. If your painted metal is looking the worse for wear, here’s how to repair it yourself without spending a fortune.

Eggers Electric Motor CO
(701) 223-6500
108 N Mandan Street
Bismarck, ND
Services
Auto Service & Repair, Water Well Drilling & Service, Electric Motors & Generators Wholesale & Manufacturers, Electric Motor Parts & Repair
Products
Electric Motors, Large

Auto Body Refinishing Inc
(701) 663-0033
3627 29 1/2 Avenue
Mandan, ND
Services
Truck Auto Body

Mandan Auto Glass
(701) 663-0474
1406 1st Street Northeast
Mandan, ND
Services
Auto Glass Repair

Dentman
(701) 663-4115
2020 46th Avenue Southeast, # G
Mandan, ND
Services
Paintless Dent Repair

Mandan Tire and Auto Center
(701) 663-9541
910 E Main Street
Mandan, ND
Services
Alignment Repair,Mufflers Repair

Duanes Body Shop Inc.
(701) 223-4924
1107 South 18th Street
Bismarck, ND
Certifications
Blue Seal Certified
Membership Organizations
National Institute for Automotive Service Excellence (ASE)

Data Provided by:
Don Resslers Auto Glass
(701) 663-4527
3729 Memorial Highway
Mandan, ND
Services
Auto Glass Repair

Saturn of Bismarck Mandan
(701) 223-2944
3344 Memorial Highway
Mandan, ND
Services
Clutch Repair,Fuel Injection Repair,Radiator Repair,SUV Repair,Tune up Repair

Trucks Trailers and More
(701) 400-7067
3015 Memorial Highway
Mandan, ND
Services
Trailer Repair,Truck Parts

Collision Center
(701) 663-0144
3729 Memorial Hwy
Mandan, ND
Services
Auto Body

Data Provided by:

DIY Wheel Repair

Do-It-Yourself Wheel Repair By Alison Lakin, Associate Editor

Scratched your wheels? We know exactly how annoying that can be. There are many tips to sprucing up your car’s paint or preventing the interior from looking worn in the first place, but the wheels need attention too – especially since they usually take the brunt of urban driving; parallel parking and curbside drop-offs are a rim’s worst nightmare. If your painted metal is looking the worse for wear, here’s how to repair it yourself without spending a fortune.

First, you’ll need the following materials:
Scratch filling primer
Wheel paint (to match your specific wheel color)
Clear lacquer
Paint thinner
Bondo spot putty
Sand paper 240 and 400 grit
Masking tape

Step 1: Remove the wheel from the car. If you choose to keep it on, make sure to fully cover the car with a cloth or paper so as to seal it from the spray of the paint.
 
Step 2: Clean the wheel. Soap-up, scrub and shine that puppy. Then use paint thinner to specifically clean the damaged area, nothing more. You want to remove all polishes and waxes from the surface in order to properly repair it, which means you’ll need to really rub the area, wipe it down and repeat.

Step 3: Once the damaged area is completely clean, you’ll need to prepare the wheel for sanding. If the tire is still on, use the masking tape to cover the area underneath where the wheel meets the tire. You can use this time to completely cover the tire to protect it from paint as well. It may be a pain, but scraping paint spray off the rubber is much worse.

Step 4: Gently sand the damaged area using 240-grit sandpaper. Once you’ve sanded it down a bit, wipe the area clean and apply the putty to the scrape. Just cover the specific area and don’t worry about getting it flat and smooth because you’ll be sanding it down. Let the putty completely dry before attempting to sand it smooth using the 400-grit sandpaper. You want to make sure it feels flush to the original wheel surface – a flat block will help to create the desired effect.

Step 5: Once again, if the wheel has not been removed from the car and tire you’ll need to fully protect any exposed areas you don’t want flakes of paint to stick to. It’ll happen, trust us.

This is where the scratch filling primer comes in. Spray it on the repair area, let dry and then sand it down with 400-grit or finer sandpaper. Add more putty if there are any uneven areas and repeat. It’s very important to clean off the overspray with a rag immediately after spraying the primer and paint. There’s no reason to get paint anywhere but the area on which you’re working.

Step 6: Now comes the painting. You’ll want to read the instructions on the spray can for the most correct application techniques. We’d recommend testing the spray paint out on some scrap metal before applyi...

Click here to read the rest of the article from DriverSide